Description
Voron 2.4 Kit update log 24/1/23:
- Omron inductive probe can now be substituted for a Voron Tap upgrade kit – please leave a note in your order.
- Includes CW2 round pancake stepper motor (LDO-36STH20-1004AHG)
- Includes PT1000 temperature sensor
- Includes 60w 24v hotend heater cartridge
- Includes Custom M1.5 – M6 size hex wrench set by Eight Tool – Made in Japan
Included Bill of Materials:
Omron G3NA-210B-DC5 (10A) or Crydom D2425 (25A) or Crydom 84134000 (10A) SSR or Panasonic AQA211VL (15A)
|
Fasteners
|
M5x40 SHCS | ||
| M5x30 BHCS | |||
| M5x16 BHCS | |||
| M5x10 BHCS | |||
| M4x6 BHCS | |||
| M3x40 SHCS | |||
| M3x30 SHCS | |||
| M3x20 SHCS | |||
| M3x16 SHCS | |||
| M3x12 SHCS | |||
| M3x8 SHCS | |||
| M3x6 BHCS | |||
| M3 Threaded Insert | |||
| M4 knurled nut | |||
| 5x10x1 Shim Ring | |||
| M3 Washer | |||
| M5 Hexnut | |||
| M3 Hexnut | |||
| M2x10 Self Tapping Screw for Plastics | |||
| M3 Hammer Head T-Nuts | |||
| 6mm x 3mm Round Neodymium Magnets | |||
| M3 T-nut HNTAJ5-3 | MISUMI HNTAJ5-3 – M3 T-NUT | ||
| M5 T-nut HNTAJ5-5 | MISUMI HNTAJ5-5 – M5 T-NUT | ||
|
Motion
|
GT2 Open Belt LL-2GT-6 (6mm wide) – Length Dependant on Config | ||
| GT2 Open Belt LL-2GT-9 (9mm wide) – Length Dependant on Config | |||
| GT2 Belt Loop (6mm wide) – 188mm | |||
| GT2 20T (6mm wide) Pulley (5mm bore) | |||
| GT2 16T (6mm wide) Pulley (5mm bore) | |||
| GT2 20T (9mm wide) Pulley (5mm bore) | |||
| GT2 20T (6mm wide) Toothed Idler (5mm bore) | |||
| GT2 20T (9mm wide) Toothed Idler (5mm bore) | |||
| GT2 80T (6mm wide) Pulley (5mm bore) | |||
| F695 2RS Bearing | |||
| 625 2RS Bearing | |||
| 5x60mm Shaft – Grind Flat | |||
| 5x30mm Shaft | |||
| Rails – 1x MGN12H 300/350/400 | |||
| Rails – 6x MGN9H 300/350/400 | |||
| Vibration Management | Printer Rubber Feet | Rubber Feet for Voron V1/V2 | |
|
Electronics / Wiring
|
Omron Mouse Button – Micro Switch | ||
| BAT85 Diode | |||
| Thermal Fuse | |||
| ZF – Rocker Switches DPST 16A ON-OFF | |||
| Fuse Medium Time Delay Acting 8A 250V Holder Cartridge 5 X 20mm Glass | |||
| TycoElectronics – 10EGG1-2 (Normal) or 10EHG1-2 (Medical): Filtered Power Inlet | |||
| Power Inlet & Rocker Switch | |||
| Fork Spade Terminal | |||
| Insulated Crimp Receptical | |||
| Nylon Cable Ties 4″ | |||
| MicroFit3 Male Pin (43031-0007) | |||
| MicroFit3 Female Pin (43030-0007) | |||
| MicroFit Connector Receptacle 4 Position (43645-0400) | |||
| MicroFit Connector Receptacle 3 Position (43645-0300) | |||
| MicroFit Connector Receptacle 2 Position (43645-0200) | |||
| MicroFit Connector Plug 4 Position (43640-0401) | |||
| MicroFit Connector Plug 3 Position (43640-0301) | |||
| MicroFit Connector Plug 2 Position (43640-0201) | |||
| MLX Power Receptacle 3 Position (50-84-2030) | |||
| MLX Power Plug 3 Position (50-84-1030) | |||
| MLX Male Pin (02-08-2004) | |||
| MLX Female Pin (02-08-1002) | |||
| JST-XH Female Pin | |||
| JST-XH Connector Plug 4 Position | |||
| JST-XH Connector Plug 3 Position | |||
| JST-XH Connector Plug 2 Position | |||
| Probe | Omron Probe TL-Q5MC2 OR Voron TAP | ||
|
Cables – Wire
|
22AWG PTFE wire (250ft total) | FEP 4 COLOR 22AWG WIRE KIT | |
| 18AWG Silicone Cable (10ft total) | FEP 3 COLOR 18AWG Wire Kit | ||
| Cables – Chain | Complete X/Y/Z Chain openable chain set | VORON CABLE CHAIN KIT | |
|
Electronics
|
NEMA17 Motor 17HS19-2004S | VORON 2 FULL MOTOR KIT by LDO | |
| Din Rail (different size for each printer) | DIN RAIL 35MM X 7.5MM 420MM | ||
| Mean Well LRS-200-24 PSU | MEANWELL LRS-200-24 | ||
| 60x60x20 Axial Fan (24V) | GDSTIME 6020 Axial Fan | ||
| 40x40x10 Axial Fan- Ball Bearing (24V) | SUNON 4010 Axial Fan | ||
| RaspberryPi4 | NA | ||
| MicroSD Card | NA | ||
| USB C Power Cable | NA | ||
| SKR 1.4 | BTT Octopus Pro | ||
| TMC2209 Stepper Motor Driver | BTT 2209×7 | ||
| Mini 12864 Display (Type B) | Mini 12864 Display | ||
| Frame | FRAME with Angled Corner Connectors | VORON 2.4 FRAME KIT by LDO | |
|
Misc
|
Bowden Tube (4mm OD, ID depends on extruder type) | Bowden PTFE Tube x3 | |
| Bowden Coupler (for 4mm OD tube) | Pneumatic Bowden Coupler Fitting 1.75mm | ||
| Foam Panel Tape (5mm wide / 3mm thick) | Raven RP59 Insulating Foam x 2 | ||
| BMG Extruder Hardware Kit | BMG Extruder Component Kit | ||
|
Panels
|
Black Panels (ABS) – Back / Deck / Bottom | ABS Panels: Voron 2.4 | |
| Clear Panels (PC) – Front / Sides / Top | PC Panels: Voron 2.4 | ||
|
Buildplate
|
Aluminum Build Plate | VORON UNIVERSAL BUILD PLATE | |
| Silicone AC Heater | V1/V2/VT Fermio Labs Bed Heater Mat | ||
| Flex Plate | VORON POWDERCOATED PEI SPRING STEEL FLEX PLATE | ||
| Build plate magnet | HIGH TEMP MAGNETIC SHEET – Graviflex® 200 | ||
| Extras | Stealthburner 5015 Fan | SUNON MF50151VX 12v Blower Fan | |
| Extras | Hotend Heater | 60W 24v HOTEND HEATER CARTRIDGE | |
| Extras | Hotend Thermistor | PT1000 TEMPERATURE SENSOR | |
| Extras | Tools – Eight Tool Hex Wrench Set – Made in Japan. | Custom set in Voron specific sizes M1.5 – M6 | |
| Extras | Bowden PTFE Tube 3mm ID – 3 metres | Bowden PTFE Tube 3mm ID – 3 metres | |
| Extras | Din Rail (different size for each printer) | DIN RAIL 35MM X 7.5MM 420MM | |
| Extras | LED set of 4 for the toolhead | NA | |
| Extras | FEP 2 Color 30AWG Wire Kit | NA | |
Additional information
| Weight | 30 kg |
|---|---|
| Size | 250mm, 300mm, 350mm |
1 review for Voron 2.4 DIY Kit – 300x300x300 – By UniquePrints
Only logged in customers who have purchased this product may leave a review.
Sean Clarke (verified owner) –
After building 2 Tridents and swapping out parts better parts purchased from Unique Prints I decided to try a 2.4 and figured I may as well start with good parts rather than replacing.
Kit is well thought out with quality components put together by someone who knows what they are doing. And Jack was super helpful swapping out some components so the printer suited my needs better.
Next printer is likely to be a 250 UP kit.