Array

Engineer PA-24 Precision Micro Terminal Crimping Pliers

$86.50 AUD inc GST

Out of stock

Engineer PA-24 are an ultra high quality and high precision crimping pliers.

  • Specialty of 2.5mm pitch connector contacts of different connector manufacturers, works with JST XH, PH, EH & NH series, Molex Micro-Fit, KK series, etc. AWG #32-#18
  • Perfectly crimps triangular insulation barrel (lugs) of DuPont (Servo) connector, Molex C-Grid III, etc. without damaging the insulations.
  • 6 Crimping Dies (‘m’-shaped crimp: 1.3, 1.6, 1.9 & 2.2mm in width & Round crimp: φ1.4 & φ1.8mm) for open-barrel contacts
  • Built-in screw cutter (M2, M2.6 & M3)
  • Tapered and slender jaws, Light weight of 115g only
  • Spring loaded (on the back side), with locking latch for easy handling
  • Made in Japan

Please see below for further information and technical specifications

Out of stock

Notify when stock available

SKU: engineer-pa-24-crimping-pliersCategories: , Tags: , , , , , ,

Description

Features
3a70bcb6 w1 9 crimp

M-shaped Dies [1.3, 1.6, 1.9 & 2.2mm in width]
The conductor barrel can be crimped securely.
The insulation barrel can be curled up very tidily.

2e11c441 round1 8 crimp

Round Dies (For DuPont contact etc.) [φ1.4 & φ1.8mm]
Wrap triangular lugs of the barrel around the insulation without damage.

9af6677a crimp samples for m 1
b5f4e462 crimp samples for o 2
9ce900a3 screw cut w
How to select the suitable crimping dies
05ab96bd measure barrels

1. Measure the width of conductor barrel or insulation barrel with a caliper while both barrel lugs are adjusted in parallel.

6dd62cb7 select dies

2. Select the die width that is close to the width of barrel lugs measured. Example: 1.5mm measured –>> Select 1.6mm dies.

47f94e14 how to crimp 2 scaled

3.
Conductor Barrel (Lug) Crimping:
It is better to offset the rearmost edge of conductor barrel (lug) 0.1-0.2 mm from the edge of the upper die to form a bellmouth on the edge of the crimped barrel. (as per the figure on the right)

Insulation Barrel (Lug) Crimping:
Set the insulation barrel (lug) at the center of the upper die in depth to keep the barrel (lug) horizontal when crimping.

Specifications
baa86127 pa 24 drg
dfe4f9d8 104650 b6eb908257fe4533a1691ff134ca64fb mv2
Item no. Dies W(mm) Dies H(mm) Dies T(mm) Wire (AWG) Ref. only
PA-24 1.3 0.5 2.2 #32 to 24
1.6 0.7 #26 to 24
1.9 0.8 #26 to 22
2.2 0.9 #24 to 18
1.4 diameter 3.2 #30 to 28
1.8 diameter #28 to 24

Additional information

Weight 0.135 kg

How to select the suitable crimping dies

Measure barrels

1. Measure the width of conductor barrel or insulation barrel with a caliper while both barrel lugs are adjusted in parallel.

Select dies

2. Select the die width that is close to the width of barrel lugs measured. Example: 1.5mm measured –>> Select 1.6mm dies.

How to Crimp 2

3.
Conductor Barrel (Lug) Crimping :
It is better to offset the rearmost edge of conductor barrel (lug) 0.1-0.2 mm from the edge of the upper die to form a bellmouth on the edge of the crimped barrel. (as per the figure on the right)

Insulation Barrel (Lug) Crimping :
Set the insulation barrel (lug) at the center of the upper die in depth to keep the barrel (lug) horizontal when crimping.

Specifications

Item no. O.A. Length Material Weight
PA-09 175mm S55C 145g
Item no. Dies W(mm) Dies H(mm) Dies T(mm) Wires applicable (Ref.)
dia. (mm) mm2 AWG (wires)
PA-09 1.0 0.50 1.7 0.200.32 0.031~0.08 #32 to 28
1.4 0.55 0.320.51 0.080.21 28 to 24
1.6 0.8 2.0 0.510.64 0.210.33 24 to 22
1.9 0.9 0.510.81 0.210.52 24 to 20

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.